tonebx
☰
BrandsPlayersGuidesNewsAll pedal typesComparisons

Pedals › EQ › MXR

MXR Ten Band EQ

MXR Ten Band EQ

EQ
List price
$159.99
Key facts
TypeTen-band graphic EQ pedal for bass or guitar1
MakerMXR (Dunlop Manufacturing)2
Current versionM108S2
BypassTrue bypass / True Hardwire12
Power18V DC, 48 mA current draw, included ECB004 18-volt adapter21
BatteryNone; cannot run on a battery5
Inputs/outputsOne input, two outputs (Output 1 to amp, Output 2 to a second amp or signal chain)2
Input impedance470 kΩ2
Output impedance5 kΩ2

The MXR Ten Band EQ is a graphic equalizer pedal from MXR, built for bass or guitar rigs, that lets you cut or boost ten fixed frequency bands to shape your tone before it reaches the amp. MXR says it lets you "tune your bass or guitar rig in seconds," with uses ranging from boosting low end to restoring treble response to a crowded pedalboard or warming up an amplified acoustic1. The current version, the M108S, carries upgrades over earlier units: noise-reduction circuitry, true bypass switching, a lightweight aluminum housing, brighter LEDs, and a second output2.

It is a level tool as much as a tone tool. Alongside the ten EQ sliders there are separate gain and volume controls, and the 18-volt operation gives the circuit extra headroom, which matters if you want to push the front of an amp or boost a solo without the EQ distorting31. A Gearnews buying guide calls it "a serious tool for both guitar and bass," noting its ten bands "from 31 Hz to 16 kHz for more surgical cuts" than a simpler EQ allows3.

What a graphic EQ does for your sound

A graphic EQ gives you a row of sliders, each tied to one frequency band. Push a slider up to boost that region, pull it down to cut it. With ten bands spaced an octave apart, the Ten Band EQ lets you address specific problems: a boomy room, a muddy low midrange, a harsh presence peak, or an amp that lacks sparkle. Because the bands are fixed, you see the curve you are building right on the pedal face, which is where the "graphic" name comes from.

MXR positions it as a rig-tuning tool: with both input and output level controls, you can compensate for level changes as you boost or cut, keeping your overall volume where you want it1. On an episode of That Pedal Show about gain, clipping, headroom and EQ, the MXR Ten Band EQ appeared among the gear used to demonstrate how EQ interacts with an overdriven amp6.

The controls: ten sliders plus gain and volume

The M108S front panel has ten EQ sliders, a gain slider, a volume slider, and a footswitch. Each EQ slider boosts or cuts its band by up to ±12 dB2. The footswitch toggles the effect on and bypass, with blue slider LEDs indicating the effect is engaged2.

ControlWhat it does
EQ sliders (10)Boost or cut ±12 dB at 31.25, 62.5, 125, 250, 500, 1K, 2K, 4K, 8K and 16K Hz21
GAIN sliderControls the amount of gain boost2
VOLUME sliderControls overall effect volume2
FOOTSWITCHToggles effect on/bypass; blue slider LEDs indicate on2

The gain and volume pair is what separates this from a bare EQ. Gain sets how hard you hit whatever comes next, while volume sets the effect's overall output level, so you can use the pedal as a boost with an EQ curve rather than only as a corrective tool. The 18-volt operation supports that role with extra headroom31.

Power and connections: 18V and two outputs

The M108S runs on 18 volts DC, drawing 48 mA, and ships with the Dunlop ECB004 18-volt adapter2. It is also compatible with Dunlop's DC Brick, Iso-Brick and Mini Iso-Brick power supplies1. There is no battery option: as one reviewer put it plainly, "you cannot operate these pedals with a battery. That is not possible."5

The 18-volt requirement means a standard 9V daisy chain or typical isolated 9V output will not power the M108S. You need the included ECB004 adapter or a power supply with an 18V output, such as Dunlop's Iso-Brick line12.

The two outputs are a practical feature. Output 1 goes to your amplifier, and Output 2 feeds a second amplifier or a completely separate signal chain21. A reviewer who compared the pedal against a budget alternative found the second output "comes in super handy if you want to split your signal"5. The pedal is mono, not stereo: it is one channel with two parallel outputs7.

Other measured specifications from the M108S manual:

SpecificationValue
Max input level+14 dBV (all sliders at 0 dB, at 1 kHz)2
Max output level+14 dBV (all sliders at 0 dB, at 1 kHz)2
Frequency response±1 dB, 20 Hz to 20 kHz2
Current draw48 mA2

Is it quiet?

The current M108S includes noise-reduction circuitry, an upgrade MXR highlights on the product page2. In a 2025 review video comparing it with a cheaper ten-band EQ, Mike of the channel Made by Miike found the MXR "pretty much dead quiet," with neither background noise nor switching clicks as loud as the competing pedal, and concluded the MXR "obviously uses the better components or better parts or is better built"5. He also tested the true bypass and found it works as advertised5.

Older units have a different reputation. Griffin Effects, a shop that offers a "Silent Night" mod service for the Ten Band EQ, says of the pedal it services: "This pedal tends to be pretty noisy meaning it has a lot of background noise."8 The M108S, by contrast, has been upgraded with noise-reduction circuitry81, which is worth weighing if you are comparing used versions.

MXR Ten Band EQ review

The Kerry King Ten Band EQ

The Kerry King Ten Band EQ (KFK1) is a signature variant of the same circuit, built around the Slayer guitarist's habit of running multiple amplifiers. According to Audiofanzine, "it's pretty much the same as the normal 10 band EQ that MXR has offered for years. The main difference is that this can be run into two amps since Kerry King likes to run multiple Marshalls."9 MXR still lists it with the same ECB004 18-volt adapter and Dunlop power supply compatibility10.

The KFK1 differs from the M108S in its slider design. Its manual describes "paragraphic" sliders that boost or attenuate up to ±18 dB at six different frequency centers, with ±12 dB filtering at 31.25, 62.5, 125, 250, 500, 1k, 2k, 4k and 8 kHz, and a ±12 dB shelf at 16 kHz112. It draws 26 mA, has a noise floor of -100 dBv (A-weighted at 5.2Vrms), and uses glow-in-the-dark graphics and sliders so it is easy to see and adjust onstage11. Audiofanzine notes the KFK1 can be powered by a 9-volt battery or an external adapter9, unlike the battery-less M108S.

One conflict worth knowing: RockBoard's listing gives the Kerry King model's power as 9V DC center negative at 26 mA1011, while MXR's own page and manual specify 18-volt operation1011.

"Overall I think MXR has the best EQ pedals out there right now, and I would more than urge you to pick up the MXR over the Boss version."
Fireguy8402, Audiofanzine9

How it fits with other MXR EQs

MXR also makes smaller EQ pedals, including the MXR Six Band EQ, which covers fewer bands in a smaller box. The Ten Band EQ's appeal is precision: ten octave-spaced bands from 31.25 Hz to 16 kHz, plus the gain and volume controls and dual outputs23. Delicious Audio's EQ buying guide summed up the current version's draw: "Noise reduction circuitry, 18v operation, and 2 separate outputs make this a flexible and powerful EQ pedal."12

For more on where an EQ belongs in a signal chain, see equalization pedals.

Videos

Strings Direct TV | MXR M108s 10-Band EQ pedal for Guitar & Bass
Strings Direct
MXR Ten Band EQ - Tips & Tricks !
Anand Mahangoe
MXR M108S 10 Band EQ Pedal - Brief Overview & Demo | Play Guitar
Rock Hard Riffs

Questions

Is the MXR Ten Band EQ true bypass?

Yes. MXR lists true bypass switching on the current Ten Band EQ, and the M108S manual specifies True Hardwire bypass. A reviewer who tested the pedal found the bypass works as advertised, so the signal passes through uncolored when the effect is off.

Can I power the MXR Ten Band EQ with 9V?

No. The M108S Ten Band EQ requires an 18-volt DC supply, and the included adapter is the Dunlop ECB004 18-volt unit. It also works with Dunlop's DC Brick, Iso-Brick and Mini Iso-Brick power supplies. A standard 9V center-negative output will not run it.

Is the MXR M108S noisy?

The current version includes noise-reduction circuitry, and a 2025 review video found it pretty much dead quiet, with no background noise or clicking. A mod shop that services the pedal describes older units as tending toward background noise, so earlier versions may be noisier than the M108S.

What are the two outputs on the MXR Ten Band EQ for?

Output 1 goes to your amplifier as usual, and Output 2 feeds a second amplifier or a second signal chain. That lets you split your rig, for example running two amps at once or sending one output to a tuner or separate effects path.

Does the MXR Ten Band EQ work on bass?

Yes. MXR describes the Ten Band EQ as a pedal for bass or guitar rigs, and the lowest slider centers at 31.25 Hz, which reaches below the open B on a five-string bass. A buying guide also calls it a serious tool for both guitar and bass.

Can the MXR M108S run on a 9V battery?

No. The M108S has no battery option and cannot be operated with a battery; it needs the 18-volt adapter that comes with it or a compatible 18-volt power supply. Plan a dedicated 18V output on your pedalboard power supply.

Sources (12)
  1. MXR® TEN BAND EQ, Dunlop (www.jimdunlop.com)
  2. M108S.pdf, Jim Dunlop, 2025
  3. The 7 Best EQ Pedals for Every Budget: Shape Your Tone in Seconds!, gearnews.com, 2025-09-15
  4. MXR® SIX BAND EQ, Dunlop (jimdunlop.com)
  5. Shootout + Opinion: MXR 10 BAND EQUALIZER (M108S) vs. JOYO BAND CONTROLLER R-12, Made by Miike (YouTube), 2025-10-13
  6. Understand Guitar Overdrive Pedals Gain, Clipping, Headroom, EQ & All That, That Pedal Show, 2020-06-26
  7. MXR KFK1 Kerry King 10 Band EQ Gui tar Effects Pedal, Music Store (www.musicstore.com)
  8. Ten Band EQ Silent Night Mod Service, Griffin Effects
  9. MXR KFK1 Ten Band Equalizer, Audiofanzine, 2026
  10. MXR® KERRY KING TEN BAND EQ, Dunlop (jimdunlop.com)
  11. KFK1.pdf, Dunlop Manufacturing, Inc., 2019
  12. 2023 UPDATE! Best EQ Pedals For Guitar: Graphic & Parametric, Delicious Audio, 2023-12-13

Other eq pedals

All eq pedals