tonebx
☰
BrandsPlayersGuidesNewsAll pedal typesComparisons

Pedals › Octave and pitch › Electro-Harmonix

Electro-Harmonix Octave Multiplexer

Electro-Harmonix Octave Multiplexer

Octave and pitchAnalogDiscontinued
Key facts
TypeAnalog sub-octave generator1
MakerElectro-Harmonix1
Released2007 (reissue); original 197712
StatusDiscontinued 20211
BypassTrue bypass1
Power9V battery included; optional 9.6VDC-200mA adapter not included1
Current draw12mA1
Dimensions4.75 x 4 x 2.25 in1
Inputs/outputsInput, Effect Out, Dry Out1

The Electro-Harmonix Octave Multiplexer is an analog sub-octave generator: it produces a deep bass tone one octave below the notes you play and blends it with your dry signal. It is a monophonic device, meaning it works only on single notes, which is typical of analog octave dividers and sets it apart from polyphonic octave pedals like the Micro POG and POG2 in the same Electro-Harmonix range1.

The pedal was discontinued in 2021, so it is now a secondhand buy. The version most players encounter is the 2007 reissue in a die-cast chassis, but the design goes back to a big box original from 197712.

What it does: an analog sub-octave for single notes

Electro-Harmonix describes the effect plainly: "Get down with deep bass tones one octave below the notes you play!"1. The circuit divides the incoming pitch by two and generates a new voice an octave down, then the BLEND knob mixes that voice against your dry signal. Because the tracking is analog, it needs a clean single note to lock onto; the maker states outright that "This is a monophonic device and works only on single notes"1.

That single-note limit is the practical difference between the Octave Multiplexer and the digital POG line. A POG or Pico POG tracks chords and stacks octaves both up and down; the Octave Multiplexer does one thing, one octave down, with the character of an analog divider. Pedal of the Day's reviewer found the pedal's smoothing filters are what set it apart, "separating the Octave Multiplexer from other octave devices"3.

The same reviewer's overall take was honest about where the pedal fits:

"The Octave Multiplexer Analog Sub-Octave Generator might not be applicable in every musical environment, but if you like to experiment and come up sounds bordering on the insane, this big silver gem is a good place to start."
Pedal of the Day3

The controls: two filters, a blend and a sub switch

The front panel has three knobs and one switch, plus the footswitch and status LED. When the LED is lit the effect is active, and the footswitch engages or disengages it1.

ControlWhat it does
BLEND knobA wet/dry knob, mixing the sub-octave voice against your dry signal1
BASS FILTER knobShapes the tone of the sub-octave's fundamental and lower order harmonics1
HIGH FILTER knobShapes the tone of the sub-octave's higher order harmonics1
SUB switchSwitches the Bass Filter in and out1

The two filters are the heart of the pedal's character. Pedal of the Day found that "the wide range from the High Filter and Bass Filter controls open up new, strange and unique sonic possibilities," and that "the Blend control makes everything more wacky the more it is increased"3. In practice, the filters let you push the generated voice from a clean sub-bass toward edgier, more synthetic territory.

The jacks are worth knowing about:

  • INPUT jack: connect your instrument here1.
  • EFFECT OUT jack: the blended output, for your amplifier1.
  • DRY OUT jack: connected directly to the input jack, so it carries your untouched signal for a second amp or a tuner1.

History and versions

The Octave Multiplexer began as a big box vintage pedal made in New York City in 19772. Pedal of the Day reviewed one of these 1970s originals, on loan from Anthony of Marla Amps, and noted that "big box, old school pedals from Electro-Harmonix are fun to play"3.

Electro-Harmonix brought the design back in 2007 in the smaller "tough and compact die-cast chassis" and discontinued it in 20211. There was also a Treadle version of the original: a schematic shows a pedal built like a wah, with switches labeled "range" and "bass" and a "Toe Down" marking near the Blend knob4.

The circuit has a life beyond the factory pedal, too. DIY builders have traced and cloned it, and one builder who documented the layout reported that a modern clone "sounds close, maybe a bit more artefact (not on every setting)" compared with the original4. The same builder noted a design detail of the original: "the original is an octave pedal and always performs at unity level, no matter the source instrument," with the clone's added JFET stage and volume control described as extra features that are not essential4.

Videos

Electro Harmonix Octave Multiplexer
ProGuitarShopDemos
Electro-Harmonix Octave Multiplexer Analog Sub Octave Generator (Demo by Dan Miller)
EHX
EHX Octave Multiplexer - Gear Up
THE MUSICIAN NETWORK (TMNtv)

Questions

Is the Electro-Harmonix Octave Multiplexer true bypass?

Yes. Electro-Harmonix lists the Octave Multiplexer as true bypass, so with the effect disengaged the dry signal passes without the pedal's circuitry in the path. A status LED lights when the effect is active, and the footswitch engages or disengages it.

Does the Octave Multiplexer track chords?

No. Electro-Harmonix describes it as a monophonic device that works only on single notes. Like other analog octave dividers, it needs one clear note at a time to generate its sub-octave voice, so chords and complex intervals will not track cleanly.

What power supply does the EHX Octave Multiplexer use?

It runs on a 9V battery, which was included, or an optional 9.6VDC-200mA power adapter, which was not included. Current draw is 12mA, low enough that battery life is long. The pedal was discontinued in 2021, so supplies are secondhand.

What is the Dry Out jack on the Octave Multiplexer for?

The Dry Out jack is wired directly to the input jack, so it carries your untouched instrument signal. You can send it to a second amplifier or a tuner while the Effect Out jack, which carries the blended wet and dry signal, goes to your main amplifier.

Is the Electro-Harmonix Octave Multiplexer discontinued?

Yes. Electro-Harmonix discontinued the Octave Multiplexer in 2021. The reissue was released in 2007 in a die-cast chassis, and the original big box version dates from 1977, so both versions are now found on the secondhand market.

Sources (4)
  1. Octave Multiplexer, Electro-Harmonix, 2021
  2. TONEHOME, TONEHOME
  3. Electro-Harmonix Octave Multiplexer Analog Sub Octave Generator, Pedal of the Day, 2026-01-25
  4. Guitar FX Layouts: Electro Harmonix Octave Multiplexer, Guitar FX Layouts (tagboardeffects.blogspot.com), 2016-09-27

Other octave and pitch pedals

All octave and pitch pedals